Servo Drive Manufacturers: How To Choose Energy Efficiency And Protocols

Oct 08, 2025 Leave a message

How to Choose Energy Efficiency and Protocols

 

Energy Efficiency Selection

 

Consider Energy Efficiency Standards

Different regions and industries have corresponding energy efficiency standards, such as IEC 61800-9-2 and EN 50598-2. These standards classify energy efficiency into different levels, with higher levels indicating more energy-efficient equipment. Manufacturers should select drives that comply with the relevant energy efficiency standards based on their target markets and application scenarios.

 

Optimize Hardware Design

Choose high-efficiency power devices, such as low-loss IGBTs, MOSFETs, or silicon carbide (SiC) devices, to reduce switching losses and conduction losses.

Optimize heat dissipation design: Use heat sinks, fans, or liquid cooling systems to lower the temperature of components, preventing efficiency degradation caused by high temperatures.

Shorten the length of power cables and motor cables, and use low-impedance cables to reduce line losses.

 

Adopt Advanced Control Algorithms

Advanced control strategies like vector control and direct torque control can more precisely regulate the operating state of motors, reducing unnecessary energy consumption. Additionally, dead-time compensation and friction compensation technologies can eliminate the impact of motor dead zones and mechanical friction, avoiding extra energy consumption caused by nonlinear factors.

Implement Energy Management Strategies

Regenerative energy feedback technology: Recycle the energy generated during motor deceleration or braking back to the power grid or energy storage capacitors, reducing power loss from resistor heating.

Dynamic bus voltage adjustment: Adjust the bus voltage in real time according to load requirements to avoid energy consumption caused by maintaining a high voltage for a long time.

Activate sleep mode when the drive is in standby or under low load to effectively reduce static losses.

 

Protocol Selection

 

Based on Application Scenario Requirements

For high-end equipment requiring multi-axis coordinated control (e.g., semiconductor wafer handling robots) with strict demands on real-time performance and synchronization accuracy, the EtherCAT protocol is an excellent choice. It can achieve a cycle time of ≤100μs and a jitter error of less than 1μs.

For medium and small-sized equipment, the CANopen protocol is more suitable. At a standard baud rate of 1Mbps, its minimum cyclic communication time is 1ms, which can meet general control needs.

 

Consider Topology Requirements

 

EtherCAT supports hybrid topologies such as linear, tree, and star structures, with a maximum of 65,535 nodes. Its daisy-chain connection method saves switch costs, making it suitable for large and complex systems.

MECHATROLINK-III adopts a ring topology and features dual-channel redundancy. It can automatically reconfigure the communication path in case of a line break, making it ideal for scenarios with high reliability requirements.

Focus on Transmission Performance Parameters

Bandwidth utilization and synchronization accuracy are key performance indicators:

EtherCAT: Bandwidth utilization can reach over 90%, with an effective data throughput of more than 80Mbps under a 100Mbps network and a DC synchronization error of <100ns.

PROFINET IRT: Bandwidth utilization is typically between 50% and 70%, with a synchronization accuracy of approximately 1μs.

Modbus TCP: Limited by the TCP/IP protocol stack, its effective utilization rate is less than 40%.

Consider Cost Factors

Hardware costs: A Modbus RTU solution only requires an RS485 chip, with a low cost of approximately $0.5 per node. An EtherCAT slave controller chip costs around $10-$15, while PROFINET IRT requires a dedicated ASIC, costing about $20-$30.

Certification fees: PROFINET compliance testing costs approximately €5,000 per device, and EtherCAT conformance testing costs around €3,000. In contrast, CANopen does not require mandatory certification.

 

Introduction to Zhejiang Tonghang E-Drive Technology Co., Ltd.

 

Technology R&D

The company has a professional R&D team dedicated to the research, development, and innovation of servo drive technology. Composed of professionals in fields such as electronic engineering, automation control, and motor technology, the team continuously explores new technologies and methods to improve the performance and energy efficiency of servo drives.

Product Features

Its servo drives may have advantages in terms of energy efficiency and protocol support:

Energy efficiency: It may adopt the aforementioned technologies such as optimized hardware design and advanced control algorithms to reduce energy consumption and improve energy utilization efficiency.

Protocol support: It may support a variety of mainstream communication protocols (e.g., EtherCAT, CANopen, Modbus) based on market demands and application scenarios, meeting the system integration needs of different customers.

Application Fields

Servo drives are widely used in various fields of industrial automation, including CNC machine tools, industrial robots, packaging machinery, and textile machinery. Zhejiang Tonghang E-Drive Technology Co., Ltd. can provide customized solutions for customers in different industries.