T3D Series

T3D series general servo driver adopts advanced full digital control and AC motor vector control theory, and is compatible with serial communication absolute encoder. It has excellent system performance and high reliability and is widely used in various general automation equipment.

T3D series Product features

 The driver instruction type is pulse type, and the motor position feedback is serial communication absolute encoder
 Adopts high-performance ARM processor chip, with excellent control performance
 Adapts to 17-bit/23-bit, single-turn/multi-turn serial communication encoder, with high positioning accuracy and good servo shaft rigidity
 Fully sealed design, good protection, strong anti-interference ability
 Compact single-board design, saving installation space
 Select the latest industrial-grade IPM module, with strong overload drive capability
 Integrates position control, speed control, and torque control
 Can drive various types of permanent magnet synchronous servo motors
 With complete fault protection and status monitoring functions

productcate-898-512

Standard Specifications And Performance Parameters For Servo Drives

 

Model L15 L20 L30 H10 H15 H25
input power supply main power supply

single phase220VAC - 15% - +10% / 50/60Hz

three - phase220VAC - 15% - +10%/50/60Hz(support)

three - phase380VAC - 15% - +10% / 50/60Hz
Environ-
ment
Temperature Work:0℃~ 40℃ Storage:-40℃~ 50℃
Humidity Work:40% ~ 80%(No condensation) Storage:Less than93%(No condensation)
Atmospheric
pressure
86kPa ~ 106 kPa
Protection level IP20
Control Model Position, speed, torque, position/speed, speed/torque, position/torque
Digital input 4 programmable input terminals (optically isolated)
Digital output 4 programmable output terminals(photoelectric isolation)
Encoder
signal
output
Signal type

A, B, Z differential output
Z signal collector open output
RS485 communication reads the feedback encoder position

Encoder feedback pulse signal output/position command synchronous pulse signal output

Position Input
frequency
T3D: Differential input:≤500kHz(kpps);Single-ended input:≤200kHz(kpps)
Command mode T3D: Pulse+symbol; Forward/reverse pulse; Orthogonal pulse
Electronic
gear ratio
1~32767/1~32767
Speed Simulate command input 0~ 10VDC ,The input impedance10kΩ
Command
acceleration
and
deceleration
Parameter settings P-060/P-061
Instruction source Analog quantity, internal speed command
Torque Simulate command input 0~+10V ,The input impedance 10kΩ
Torque limit Parameter settings P-065/P-066
Instruction source Analog quantity, internal torque instruction
Monitoring function Speed, current position, position deviation, motor torque, motor current, command
pulse frequency, etc
Protection function Over-speed, overvoltage, over-current, overload, brake anomaly, encoder anomaly,
position error, command over-frequency, etc
Characteristic Speed frequencyre sponse ≥1.6kHz
Speed
fluctuation rate
< ±0.03%(Load 0~100%); < ±0.02%(Power -15% ~ +10%)

 

Introduction to the Operation Panel

 

page-197-132

Efficiency leap Precision and stability

 

The T3D series panel consists of 5 LED digital tube displays and 4 buttons: ▲、▼、◄、【SET】, used to display various system statuses and set parameters.The operations are all hierarchical operations, which are expanded layer by layer from the main menu. The operation panel is shown in the following figure:

Symbol

Name

Function

POW

Power light (none)

The decimal light on the second digital tubefrom the leftindicates servo undervoltage

RUN

Running light (none)

The decimal light on the first digital tubefrom the left indicates that the servo is enabled

▲

Add keys

Add serial numbers or numerical values;Long pressing has a repeating effect.

▼

Reduce keys Reduce the serial number or numerical value;Long pressing has a repeating effect.

◄

Exit button

Menu exit, operation canceled.

SET

Confirm button Menu access; Parameter modificationconfirmation or operation confirmation.

 

T3D Series Servo Drive External Dimensions(mm) 

 

page-800-580

Driver size one (model T3D-L15/L20)

Figure 1 installation dimension diagram ofT3D-L15/L20 (unit: mm)

page-800-580

Driver size three (model T3D-H10/H15/H25)

Figure 2 T3D-L30 installation dimensions (unit: mm)

page-800-580

Driver size two (model T3D-L30)

Figure 3 T3D-H10/H15/H25 installation dimensions (unit: mm)

 T3d Servo Drive Wiring Diagram

productcate-735-387
T3D-L15A/L20A/B Wiring diagram
productcate-735-387
T3D-L30A Wiring diagram
productcate-735-387
T3D-H10/H15/25 Wiring diagram

Control Wiring Diagram

 

productcate-718-795

Special attention:

  • If the pulse command signal is 24V power supply, PULS+ must be connected to pin 39 of CN1, and SIGN+ must be connected to pin 38 of CN1, otherwise the pulse command port may be damaged.
  • If the pulse command signal is 5V power supply, PULS+ must be connected to pin 25 of CN1, and SIGN+ must be connected to pin 24 of CN1, otherwise the pulse reception may be abnormal.

TH-T3D-L15A-GABN

TH-T3D-L15A-GABN 1
TH-T3D-L15A-GABN 2
TH-T3D-L15A-GABN 3
TH-T3D-L15A-GABN 4
TH-T3D-L15A-GABN 5

TH-T3D-L20A-RABF

TH-T3D-L20A-RABF 1
TH-T3D-L20A-RABF 2
TH-T3D-L20A-RABF 3
TH-T3D-L20A-RABF 4
TH-T3D-L20A-RABF 5
TH-T3D-L20A-RABF 6
TH-T3D-L20A-RABF 7
TH-T3D-L20A-RABF 8

TH-T3D-L30A-RABF

TH-T3D-L30A-RABF 6
TH-T3D-L30A-RABF 1
TH-T3D-L30A-RABF 1
TH-T3D-L30A-RABF 2
TH-T3D-L30A-RABF 1
TH-T3D-L30A-RABF 3
TH-T3D-L30A-RABF 4
TH-T3D-L30A-RABF 5

Zhejiang Tonghang E-Drive Technology Co., Ltd. is one of the leading t3d series manufacturers and suppliers in China. We warmly welcome you to buy the best t3d series at competitive price from our factory. For more company information, contact us now.

servo drives